Amer Networks WAP200N Spezifikationen

WAP200N Wireless-N AP

WAP200N Wireless-N AP z Rear Panel From L to R ：（ ） POWER The jack is used to connect the included 12V DC power adapter. LAN The Gigabit Eth

WAP200N Wireless-N AP second, the WPS function will be enabled. Antenna The detachable antenna is for wireless radio transmitting and receiving.

WAP200N Wireless-N AP Chapter 2 Hardware Installation This chapter explains how to connect the Access Point (take the AP mode installation as ex

WAP200N Wireless-N AP The topology plan of AP mode connection 9

WAP200N Wireless-N AP Chapter 3 Web Configuration 3.1 Web Login Connect to the WAP200N via wired cable and configure 192.168.0.x(x ranges 1-253)

WAP200N Wireless-N AP Click OK to enter the first web page of the device. 11

WAP200N Wireless-N AP 3.2 Wizard Click “Next” in the first page and the next page appears. On this page, you can select from five wireless ne

WAP200N Wireless-N AP 3.3 Running Status This page shows the wireless AP’s current status, including wireless status, LAN status and system infor

WAP200N Wireless-N AP Channel, Encryption mode, etc. z LAN Interface information This shows the LAN IP obtain way, MAC address, IP address, subne

WAP200N Wireless-N AP address, subnet mask and gateway manually for the device. Dynamic IP：Automatically obtain IP address, subnet mask and gate

WAP200N Wireless-N AP Copyright Statement is the registered trademark of Amer.com Corp. All the products and product names mentioned herein are t

WAP200N Wireless-N AP Chapter 4 Wireless Settings 4.1 Working Mode Select “Wireless Setting->Working Mode” to enter the following window. From

WAP200N Wireless-N AP Next, this user guide will explain the five modes one by one: 4.1.1 Access Point (AP) Mode The AP mode is the basic mode o

WAP200N Wireless-N AP 4.1.1.2 AP Mode Settings In the working mode, select “AP” to enter the next window. 18

WAP200N Wireless-N AP z Basic Wireless Settings  Network Mode：Select one mode from the following. The default is 11b/g/n mode. 11b mode：Allow

WAP200N Wireless-N AP auto-negotiation speed, and 11n wireless client to connect the device with 11g speed. 11b/g/n mode：Allow 11b/g/n-compliant c

WAP200N Wireless-N AP communication of wireless clients connected with the same SSID.  AP Isolation: One access control feature based on wirele

WAP200N Wireless-N AP wireless network. In IEEE802.11, BSSID is the MAC address of wireless access point.  Channel：Specify the effective channe

WAP200N Wireless-N AP Mixed WEP WEP (Wired Equivalent Privacy), a basic encryption method, usually encrypts wireless data using a series of digit

WAP200N Wireless-N AP Setting Explanation  Select SSID：Select the SSID (main SSID or minor SSID) to configure security setting from the drop-dow

WAP200N Wireless-N AP enter the following window: Setting Explanation  Select SSID：Select the SSID (main SSID or minor SSID) to configure sec

WAP200N Wireless-N AP Content Chapter 1 Product Overview ...1 1.1 Features ...2 1.2

WAP200N Wireless-N AP WPA2-PSK WPA2 provides more secure features than WEP and WPA. Select “WPA2-PSK” from the drop-down menu to enter the followi

WAP200N Wireless-N AP  Pass Phrase： Enter the encrypted characters with 8-63 ASCII characters.  Key renewal Interval：Set the key’s renewal per

WAP200N Wireless-N AP [Advanced Encryption Standard]. The default is TKIP mode.  Key Renewal Interval：Set the key’s renewal period.  Radius Se

WAP200N Wireless-N AP Setting Explanation  Select SSID：Select the SSID (main SSID or minor SSID) to configure security setting from the drop-do

WAP200N Wireless-N AP The default is 1812.  Shared Key：Enter the shared key for authentication server with 8~63 ASCII characters.  Session Tim

WAP200N Wireless-N AP 802.1x Authentication This security mode is used when a RADIUS server is connected to the device. 802.1x, is a Port-based a

WAP200N Wireless-N AP Setting Explanation  Select SSID：Select the SSID (main SSID or minor SSID) to configure security setting from the drop-dow

WAP200N Wireless-N AP 4.1.2 P2P (Point to Point) Bridge Mode Two wired local networks communicate and share network resource via two WAP200N’s wir

WAP200N Wireless-N AP 4.1.2.2 P2P Bridge Setting In the working mode, select “WDS P2P” to enter the next screen. z Basic wireless Settings  N

WAP200N Wireless-N AP maximum speed of 11Mbps.  11g mode：Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed o

WAP200N Wireless-N AP 4.3 WPS Settings...56 4.4 Access Control...58 4.5 Connection

WAP200N Wireless-N AP the MAC address of wireless access point.  Channel：Specify the effective channel (from 1 to 13\Auto) of the wireless netw

WAP200N Wireless-N AP TKIP Encryption Description  Pass Phrase：Enter the encrypted characters with 8-63 ASCII characters. AES Encryption Descri

WAP200N Wireless-N AP 4.1.3 P2MP Bridge Mode The P2MP Bridge Mode which connects scattered wired network together is more complicated than P2P Br

WAP200N Wireless-N AP least two wireless APs are needed. For better performance, it is recommended to use an AP of the same model. 4.1.3.2 P2MP

WAP200N Wireless-N AP z Basic wireless Settings  Network Mode：Select one mode from the following. The default is 11b/g/n mode.  11b mode：Allo

WAP200N Wireless-N AP  BSSID：Basic Service Set Identifier of wireless network. In IEEE802.11, BSSID is the MAC address of wireless access point.

WAP200N Wireless-N AP TKIP Encryption Description  Pass Phrase：Enter the encrypted characters with 8-63 ASCII characters. AES Encryption Descri

WAP200N Wireless-N AP 4.1.4 Wireless Repeater Mode Repeater Mode can repeat and amplify wireless signals to extend the wireless network coverage.

WAP200N Wireless-N AP z Basic wireless Settings  Network Mode：Select one mode from the following. The default is 11b/g/n mode.  11b mode：A

WAP200N Wireless-N AP maximum speed of 11Mbps.  11g mode：Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed o

WAP200N Wireless-N AP Chapter 1 Product Overview WAP200N is an IEEE802.11n (Draft 2.0)-compliant wireless access point with one Gigabit LAN switc

WAP200N Wireless-N AP communicate with each other. For example, configure main SSID as AP1, minor SSID as AP2. PC1 and PC2 connect to AP1 via wire

WAP200N Wireless-N AP feature is to isolate the communication of wireless clients connected with different SSID. Tip: If you want to isolate all c

WAP200N Wireless-N AP More details please refer to 4.1.1.2. z Wireless Distribution System (WDS)Setting  Encryption Type：Select the data encr

WAP200N Wireless-N AP  AP MAC Address：Input the MAC addresses (no more than four) of remote access points by manual or open scan. MAC Address 1

WAP200N Wireless-N AP 4.1.5 Wireless Client Mode In this mode, connect the device’s LAN port to wired network adapter port. In this case, the AP

WAP200N Wireless-N AP 4.1.5.2 Client Mode Settings In the working mode, select “Client” to enter the next window.  Security Mode：Select wirel

WAP200N Wireless-N AP ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) Or 10/26 hex characters.  Default Key：Sele

WAP200N Wireless-N AP AP MAC address. Select one and Click “Save” to complete this part’s setting. The AP will reboot automatically, and then the

WAP200N Wireless-N AP 4.2 Advanced Settings This section mainly deals with wireless advanced settings, including Speed, Beacon Interval, Fragment

WAP200N Wireless-N AP default value is (1-2-5.5-11Mbps…). It is recommended not to modify the default value.  Beacon Interval：The frequency inte

WAP200N Wireless-N AP 1.1 Features ¾ Complies with IEEE802.11n (Draft 2.0), IEEE802.11b and IEEE802.11g standards ¾ Supports five working modes

WAP200N Wireless-N AP 4.3 WPS Settings WPS (Wi-Fi Protected Setting) can be easy and quick to establish the connection between the wireless netwo

WAP200N Wireless-N AP Setting Explanation：  WPS settings：To enable or disable WPS function. The default is “disable”.  WPS mode：Provide two wa

WAP200N Wireless-N AP restore to default setting. The access client has to support WPS function when you implement WPS settings. 4.4 Access Contr

WAP200N Wireless-N AP access the wireless network.  MAC Address Management：Input the MAC address to implement the filter policy. Click “Add” to

WAP200N Wireless-N AP 4.5 Connection Status This page shows wireless client’s connection status, including MAC address, Channel bandwidth, etc. S

WAP200N Wireless-N AP 4.6 PING Ping is used to check a device’s connectivity. If the connecting device has established connection with the AP, th

WAP200N Wireless-N AP Chapter 5 SNMP Setting 5.1 SNMP Introduction Simple Network Management Protocol (SNMP) is a popular protocol for network m

WAP200N Wireless-N AP 5.2 SNMP Setting This device supports SNMP v1 and SNMP v2c. Please click “SNMP Setting” in the left page to enter the follo

WAP200N Wireless-N AP  Read/Write Community: Indicates the community read/write access string to permit reading and re-writing this AP’s SNMP in

WAP200N Wireless-N AP Chapter 6 System Tools This section focuses on how to maintain the AP, including Restore to Factory Default Setting, Backu

WAP200N Wireless-N AP Bridge, WDS P2MP Bridge, WDS AP Bridge and Client ¾ Supports Auto MDI/MDIX ¾ Supports Firefox1.0, IE5.5 or above ¾ Suppo

WAP200N Wireless-N AP User Name: Enter a new user name for the device. Old Password: Enter the old password. New Password: Enter a new password. R

WAP200N Wireless-N AP 6.3 Backup/Restore The device provides backup/restore settings, so you need to set a directory to backup these settings

WAP200N Wireless-N AP 6.4 Time Settings This section is to select the time zone for your location. You can select your own time or obtain the sta

WAP200N Wireless-N AP 6.5 Reboot System This page is used to reboot the wireless access point. Rebooting the device makes the settings configured

WAP200N Wireless-N AP Upgrade Steps：1. Download the higher firmware version from our website: www.Amer.com. 2. Extract the firmware file on yo

WAP200N Wireless-N AP 6.7 Syslog The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown i

WAP200N Wireless-N AP Appendix I: Glossary Access Point(AP): Any entity that has station functionality and provides access to the distribution s

WAP200N Wireless-N AP this setting is the same for all devices in your wireless network. WEP: Wired Equivalent Privacy (WEP) is the method f

WAP200N Wireless-N AP product use different method for key generation, it might not work for different products. Therefore, it is NOT recommend u

WAP200N Wireless-N AP Appendix II: TCP/IP Address Setting (Take Winxp as example) Click the “Start—>Settings—>Control Panel” (Fig- 1):

WAP200N Wireless-N AP If any of listed items are missing or damaged, please contact the Amer.com reseller from whom you purchased for replacement

WAP200N Wireless-N AP Choose “Local Area Connection”, right-click on the icon, choose the “Properties”, then the “Local Area Connection Pro

WAP200N Wireless-N AP Choose the “Use the following IP address”, enter the IP address as: 192.168.0.xxx. (xxx ranges 1~253), Subnet mask is: 255.2

WAP200N Wireless-N AP POWER When it turns green, indicates the unit has power. SYS When it turns green, a blinking light indicates the system